DIY Security Systems
Regardless of the type of vehicle or product, it’s essential that your dashcam installation is set up correctly, or you may miss valuable video footage when accidents happen. Learning how to install dash cam back camera may seem complicated, but we’re going to make sure your rear camera installation goes smoothly with our instructions.
What Is a Dash Cam Back Camera?
A rearview camera, also known as a back camera, helps you to see what is behind your car without looking backward. Although the device comes standard with several new car brands, if it didn’t come with one, you can attach a back camera to your car. Dual camera versions have a second secondary camera for the vehicle’s back, or a camera supporting the rider.
The neatest and simplest place to attach the wiring for the rear camera when mounting a dual dash monitor is down the A post, just below the kick panels of the door and towards the boot or cover.
The Features of the Back Camera
If you look at a dash camera’s settings, the extra features can appear. Here’s some clarification of standard dash camera features:
Auto Recording
It starts recording automatically when the car is on and stops when the vehicle is turned off.
Loop Recording
The monitor can erase the oldest images, rather than avoid capturing them until they are complete. Any footage you want to save will have to be locked manually.
G-Sensor
Enables the camera to recognize the force of a collision, and to lock the recordings automatically to avoid overwriting.
Park Mode
Uses the G-Sensor to determine whether the parking car is struck and start recording.
ADAS – Advanced Driver Assistance
A dashcam should provide a warning of lane deviation and a warning of collision forward. The camera warns the driver if they wander off the road, or are too tight to another car.
What Is the Best Resolution for a Back Camera?
Before you learn how to install dash cam back camera in your car, you must first know the best resolution for a dashcam. Many dash cameras can deliver various resolutions that impact the video quality; and how much power it needs. The picture captured is bigger and simpler to read a license plate, and information is higher the size.
The primary point is VGA or 480P, moving on to 720P HD quality from there, and on to 1080P Full HD video, Super High Definition 1296P, and most recently, 2160p or extremely high Definition 4K.
How to Install Dash Cam Back Camera
The wire will feed out via the number plate, where the device can be mounted above the license plate in several cases. To position a rear camera properly, here is the step-by-step guide on how to install dash cam back camera:
- Remove your license plate at the rear. Remove each of the screws holding your rear plate number in the area using a Phillips head screwdriver. Then, remove the plate and put it aside.
- Remove the interior panel of the car’s trunk. Kick open the trunk and search for a sturdy internal sheet that will protect the opposite direction of the license plate’s mounting portion. Then plug, and pry off, a trim extraction tool or another thin device behind the board.
- Drill a hole within the mounting area of the license plate. Make sure no obstructions exist between the mounting of the license plate and the rear circuit board chamber. Instead, using a power drill fitted with a high-speed twist drill bit to create a tiny hole within the vehicle. Set up the hole, and the camera’s control and video cable can travel directly behind it.
- Run the camera wiring into your trunk. Pull the split end of the video and power cable for your camera through the drilled hole into your car’s trunk. Pull it close enough that the rubber grommet lodges into the drilled tube.
- Fuse the reverse light wires with the camera wires. Add 1 of your bare wire cables to the control connection on the camera chain. Then, poke and twist your bare wires through the middle of the uncovered reverse light wires. For protection, ensure the merged wires are covered in electrical tape.
- Route the video cable from your device to the front of the vehicle. Connect your RCA cable to the video connector of the camera cord, if required. Based on the type of car, you would be able to peel back the headliner or side panels of the automobile and dragging the cable into the open space.
- Add internal controls to the mirror or camera frame at the rearview. You’ll need to strap the new device onto your existing rearview mirror for specific internal cameras. You’ll have to cut the mirror off for everyone and slip the display onto the pre-existing mirror frame.
- Link camera cable from your computer to the RCA line. After connecting the splitter cable on your computer, attach the camera end of the wire to the RCA cord on your device. The attached wires are then covered with electrical tape to tie them together.
- Connect the fuse tap into the fuse box. Locate, and unlock, your fuse box. Then, insert the tap into an open fuse tube. Check the lid of your fuse box or the instruction manual for your car to see which slots are accessible if need be.
- Link your backup camera to the cable for control and recording. When you have mounted the rearview display and all the appropriate camera cables, return to the back of your vehicle. If required, close the trunk and then attach the backup camera to its electricity and video cable.
- Place the device onto your license plate. If the camera is attached to the front of your license plate, fix the plate, and follow directions provided by the manufacturer. When the device clips to the back of your license plate, line the tool across them with the fastener holes and thread screws on the board.
- Put your license plate and trim panels back in. Place your rear license plate back into the car using a Phillips head screwdriver. When reattached, offer firm tugs to the plate number and rearview camera to ensure they are protected.
Conclusion
With an hour of work, you will feel safer and confident once you’re driving or parking your car. Following this guide on how to install dash cam back camera allows you to see your car’s rear. Without going through the troubles of getting into an accident and providing evidence of whose fault it is, you and your family would feel much safer now. Know more about Dash Cameras.